Manure Fork DG
The SAPHIR DG manure fork serves for unloading and transport of loose manure, straw, vegetation, shrubs, etc. The SAPHIR manure forks are delivered with high-quality tines from SHW. The standard tine length is 800 mm.
|
Wear strip on the tine support pipe
Overlapping of the rear wall over the tine support pipe for especially high stability Thick-walled tine support pipe with welded conical sleeves |
Stable parking foot for safe stability of the machine
Optional side tines for loss reduction during transport |
Manure Fork DG XL
The large-size SAPHIR manure fork XL serves for unloading and transport of loose manure, straw, vegetation, shrubs, etc.. The SAPHIR manure fork XL includes only heavy-duty high-quality tines from SHW of a length of 800 mm as standard.
|
Wear strip on the tine support pipe
Thick-walled tine support pipe with welded conical sleeves, reinforcement bushes and rear wall reinforcement High fork back with a height of 860 mm (optionally additional 350 mm are possible) |
Optional side steel tines for loss reduction during transport
Overlapping of the rear wall over the tine support pipe for especially high stability |
Manure Fork with Hydraulic Hold-Down Device DGN
The SAPHIR manure fork with hydraulic hold-down is used to transport loose manure, straw, vegetation, shrubs etc. A particular advantage of the tool is the very large opening width of 1,220 mm. The hold-down is opened and closed as standard by one or two double-acting hydraulic cylinders.
|
Wear strip on the tine support pipe
Thick-walled tine support pipe with welded conical sleeves Large approx. 1,220 mm opening width High-quality tines (800 mm) from SHW |
Two double-acting hydraulic cylinders with pressure control valve
High fork back (800 mm) Optional wall withdrawal on request |
Manure & Silage Cutter DSZ
SAPHIR DSZ manure and silage cutters/ feeders are intended for removing grass and maize silage, for mucking out manure and for transporting loose dung, straw, vegetation and shrubs. A particular advantage of the device is the very large 1,400 mm wide opening.
The anti-twist tines ensure that items are picked up easily. The side tines ensure that items are transported with the lowest possible losses.
The anti-twist tines ensure that items are picked up easily. The side tines ensure that items are transported with the lowest possible losses.
|
Wear strip on the thick-walled tine support pipe
Welded in conical bushes Hydraulic upper gripper with two double-acting, end-cushioned hydraulic cylinders Very large opening width of 1,400 mm |
Low-maintenance, replaceable slide bearings
With side, pointy bent tines (600 mm) High-quality tines from SHW with 800 mm normal load tines or 1000 mm heavy-duty tines (L-version) |
Manure & Silage Cutter DSZ XL
SAPHIR manure and silage cutters XL are intended for removing grass and maize silage, for mucking out manure and for transporting loose dung, straw, vegetation and shrubs. A decisive advantage of the DSZ XL is the particularly large capacity and the very wide opening width of approx. 2,000 mm. The anti-twist heavy-duty tines ensure that items are picked up easily. The side tines give the transported goods an additional side support for the lowest possible losses.
|
Wear strip on the thick-walled tine support pipe
Welded in conical bushes Hydraulic upper gripper with two double-acting, end-cushioned hydraulic cylinders Anti-twist heavy-duty tines in the upper gripper |
Very large opening width of the upper gripper of 2,000 mm
Low-maintenance, replaceable slide bearings High-quality heavy-duty tines (1,250 mm) from SHW |
Silage Cutting Pliers SSZ
SAPHIR silage cutting pliers SSZ are suitable for removing and transporting any type of silage. The counter blades placed on both the right and left of the back section ensure a clean cut without the risk of material jams. The gap between the upper gripper and the basic machine can be set by the innovative re-tensioning device so that material jams are reduced to a minimum. The back of the silage cutting pliers is closed with expanded metal. This enables particularly good visibility. Another unique selling point of the SAPHIR silage cutting pliers is the double-wall upper gripper design.
|
Thick-walled tine support pipe (outer tines in heavy-duty design) with welded conical bushes
Tine support pipe protected by additional low-wear bar (500 HB) Screwed-in front blade can be either serrated or corrugated Back wall with side counter blades |
Double-walled, reinforced upper gripper with very wide opening (850 mm)
The particularly large overbite (approx. 160 mm) guarantees a clean cut without tearing. Re-tensioning device of upper gripper |
Silage Cutting Pliers SSZ XL
|
The SAPHIR silage cutting pliers XL are suitable for removing and transporting any type of silage. The particular feature of the XL product range is the very large capacity and the wide opening width of the upper gripper of approx. 1300 mm. The counter blades placed on both the right and left of the back section ensure a clean cut without the risk of material jams. The gap between the upper gripper and the basic machine can be set by the innovative re-tensioning device so that material jams are reduced to a minimum. The back of the silage cutting pliers is closed with expanded metal. This enables particularly good visibility. Another unique selling point of the SAPHIR silage cutting pliers is the double-wall upper gripper design. The particularly large overbite (approx. 160 mm) guarantees a clean cut without tearing.
|
|
|
Thick-walled tine support pipe with welded conical sleeves
Tine support pipe protected by additional highly wear-resistant bar ( 500 HB ) Screwed-in front blade can be either serrated or corrugated Back wall with side counter blades |
Double-walled, reinforced upper gripper with very wide opening 1,300 mm
Re-tensioning device for upper gripper Optional lifting frame for attaching to the rear or front hydraulic system with an additional lifting height of approx. 2,000 mm ( 1 x dw required) |
Silage Cutting Pliers - Special Equipment
The hydraulic push off wall for silage cutting pliers allows the silage block to be deposited by easy pushing out. In addition, due to the cut-off wall additional discharge heights can be achieved on the mixing vehicle. A double-action control unit is required ( + 1x dw ).
|
|
Drive-off ramp for silage cutting pliers: The drive-off ramp is used to load loose bulk goods in the silage area, such as loose silage, concentrated feed and feed additives. The drive-off ramp is quickly taken by the silage cutting pliers and can also be replaced quickly
again. These processes can be carried out without getting out of the host vehicle. Caution! NO cutting can take place with the drive-off ramp installed!
again. These processes can be carried out without getting out of the host vehicle. Caution! NO cutting can take place with the drive-off ramp installed!
Silage Comb SK, Grain Sliding Plate GS & Extension VL
|
|
|
The SAPHIR silage comb SK is the optimum working tool for getting silage down from especially high silo stocks. The adjustable front handle ensures particularly adaptable, optimum work. The safe cutting off of silage at a great height protects people and machines.
SAPHIR grain sliding plate type GS is a simple, rigid plate for attaching to the rear or front hydraulic system or to our SAPHIR extension type VL. The blade is ftted with a screwed-in scraper bar made of highly wear-resistant steel.
The SAPHIR extension can universally be combined with any of our grain pushers and also our silage combs.
SAPHIR grain sliding plate type GS is a simple, rigid plate for attaching to the rear or front hydraulic system or to our SAPHIR extension type VL. The blade is ftted with a screwed-in scraper bar made of highly wear-resistant steel.
The SAPHIR extension can universally be combined with any of our grain pushers and also our silage combs.
|
Thick-walled tine support pipe with welded cylinder sleeves
Adjustable front grip for adapted silage withdrawal. With anti-twist normal-load tines from SHW 800 mm as standard. |
Highly wear-resistant scraper bars 200 x 20 mm (500 HB)
Optional plastic scraper bar Round blade body Parking support Compact design |
Pallet Fork PG
|
The SAPHIR pallet fork PG features robustness with simultaneously best possible visibility. The forged quality
forks (made in Germany) are protected from abrasion by an additional wearing zone in the bent area.
|
Pallet Fork Combi PGK
|
The SAPHIR pallet fork Kombi has as standard attachment options for euro attachments and Cat. II three point linkage for the front and rear hydraulic system. The attachment combination is always available without needing any retro-fitting works.
Load-bearing capacity of max. 2,500 kg (centre of gravity at 500 mm)
|
Forklift Rotator KDG
|
The SAPHIR forklift rotator allows taking and emptying of crates. The tipping angle of 180° - 220°guarantees
emptying of each crate without leaving residues. The forklift rotator is designed for crates of a maximum width of 1,600 mm. Depending on the demand, the machine can be aligned for clockwise or counter-clockwise rotation.
|
Rear Pallet Fork PGH
|
The SAPHIR rear pallet fork is a functional, light pallet fork for fiting to the rear hydraulic system.
|
Adaptor Frame ADAP
The most different adapters can be produced for tractors, farm, wheeled, and telescopic loaders. With this, forepart dimension and tipping angle are optimally designed. On the side of the attachment, usually a mechanical locking device is integrated in the adaptors.
